®
Netopia 3346-ENT/3356-ENT ADSL Router
Getting Started Guide
All Models
Contents
Chapter 1 — Introduction..........................................................1-5
Overview....................................................................... 1-5
Features and Capabilities............................................... 1-5
How to Use this Guide.................................................... 1-6
What You Need.............................................................. 2-1
Important Safety Instructions ......................................... 2-2
POWER SUPPLY INSTALLATION.............................. 2-2
Identify the Connectors and Attach the Cables................. 2-3
Readying Computers on Your Local Network..................... 3-1
Connecting to an Ethernet Network ................................. 3-2
Chapter 4 — Sharing the Connection.........................................4-1
Configuring TCP/IP on Windows-based Computers............ 4-1
Microsoft Windows......................................................... 4-1
Configuring TCP/IP on Macintosh Computers ................... 4-2
Macintosh MacOS 8 or higher or Mac OS X...................... 4-3
Chapter 5 — Telnet-Based Management....................................5-1
Connecting through a Telnet Session............................... 5-2
Configuring Telnet software ................................... 5-2
Navigating through the Telnet Screens............................. 5-3
Accessing the Easy Setup Telnet screens............... 6-1
Quick Easy Setup Connection Path.................................. 6-2
1. ADSL Line Configuration ................................... 6-4
2. Easy Setup Profile............................................ 6-5
3. IP Easy Setup .................................................. 6-6
4
Getting Started Guide
4. Easy Setup Security Configuration ..................... 6-8
Important Safety Instructions ......................................... A-4
47CFR Part 68 Information............................................. A-5
FCC Requirements ............................................... A-5
FCC Statements................................................... A-5
Electrical Safety Advisory ............................................... A-6
Introduction 1-5
Chapter 1
Introduction
Overview
The Netopia 4-port ADSL Router (3346-ENT/3356-ENT, DE, EU models) is a full-featured, stand-alone DSL
router for connecting diverse local area networks (LANs) to the Internet and other remote networks. The Netopia
4-port ADSL Router uses a high performance ADSL line to provide your whole network with a high-speed
connection to the outside world.
This section covers the following topics:
•
•
“Features and Capabilities” on page 1-5
“How to Use this Guide” on page 1-6
Features and Capabilities
The Netopia 4-port ADSL Router provides the following features:
•
ADSL WAN interface supports asymmetric data rates from 32 Kbps to 8 Mbps downstream and 32 Kbps to
800 Kbps upstream over an RJ-11 interface
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
ADSL WAN interface supports ADSL Annex A and Annex B
Interoperable with all major ADSL DSLAM vendors
LAN interface: four port 10/100BaseTX Ethernet switch with Auto-crossover support, RJ-45
Support for up to 8 ATM (AAL5) PVCs
Bridged or routed Ethernet encapsulation, LLC/SNAP and VC Multiplexing (RFC 1483/RFC 2684)
1.610 OAM F5 Loopback
ATM QoS: UBR, CBR
Point-to-Point Protocol (PAP/CHAP authentication)
PPP over Ethernet Gateway
PPP over ATM Gateway: LLC and VC Multiplexing
PPP over Ethernet pass-through
Transparent bridging option
Support for IP routing for Internet connectivity
Numbered or unnumbered WAN interface
Support for Ethernet LANs with up to eight Ethernet IP subnets
1-6 Getting Started Guide
•
•
•
•
•
•
•
•
NAT/NAPT, Multi-NAT, and DHCP (client, server, and relay) for security and convenience
DNS proxy
IP Multicast Forwarding, IGMP V1, V2
RIP1 and RIP2, static routes
IP QoS: TOS bit prioritization
VPN Pass-through for PPTP and IPSec
Built-in VPN gateway features offer support for up to 15 PPTP or IPSec VPN tunnels
IPSec implementation supports DES or 3DES encryption, MD5 or SHA1 encapsulation, and manual or IKE
keying
•
•
•
•
•
•
•
•
•
•
•
•
Built-in firewall protects LAN resources from Internet intruders
Backup Default Gateway feature with an external router enables high-availability solutions
Menu-driven or CLI interfaces via Telnet
Easy Setup with menu-driven interface
Tiered Access, 2 levels of configuration access
Configuration Management, up to 3 backup configurations
TFTP download/upload of new firmware and configuration files
System diagnostics and logs
SNMP V1 and V2 (read/write access)
Management utilities: ICMP ping, traceroute, Telnet client, and Syslog client
Status lights (LEDs) for easy monitoring and troubleshooting
Wall-mountable, Bookshelf (Side-stackable), or Desktop-stackable design for efficient space usage
How to Use this Guide
In addition to the documentation contained in the accompanying Firmware User’s Guide, this guide is designed
to get you up and running and connected to your local area network and the Internet. It is intended to be viewed
on-line, using the powerful features of the Adobe Acrobat Reader. The information display has been deliberately
designed to present the maximum information in the minimum space on your screen. You can keep this
document open while you perform any of the procedures described, and find useful information about the
procedure you are performing.
You can also print out all of the manual, or individual sections, if you prefer to work from hard copy rather than
on-line documentation. The pages are formatted to print on standard 8 1/2 by 11 inch paper. We recommend
that you print on 3-hole punched paper, so that you can put the pages in a binder for future reference.
This guide is organized into chapters describing the Netopia 4-port’s advanced features. You may want to read
each chapter’s introductory section to familiarize yourself with the various features available.
Use the guide’s table of contents and index to locate informational topics.
Making the Physical Connections 2-1
Chapter 2
This section tells you how to make the physical connections to your Netopia 4-port ADSL Router. This section
•
•
•
•
“Find a Location” on page 2-1
“What You Need” on page 2-1
“Identify the Connectors and Attach the Cables” on page 2-3
“Netopia 4-port ADSL Router Status Lights” on page 2-5
Find a Location
When choosing a location for the Netopia ADSL Router, consider:
•
•
Available space and ease of installation
Physical layout of the building and how to best use the physical space available for connecting your Netopia
4-port ADSL Router to the LAN
•
•
•
•
•
Available wiring and jacks
Distance from the point of installation to the next device (length of cable or wall wiring)
Ease of access to the front of the unit for configuration and monitoring
Ease of access to the back of the unit for checking and changing cables
Cable length and network size limitations when expanding networks
For small networks, install the Netopia 4-port near one of the LANs. For large networks, you can install the
Netopia 4-port in a wiring closet or a central network administration site.
WhatYou Need
Locate all items that you need for the installation.
Included in your router package are:
•
•
•
•
•
The Netopia 4-port ADSL Router
A power adapter and cord
One Category 5 Ethernet cable
One DSL WAN (or Line) cable
The Netopia CD containing software and documentation
2-2 Getting Started Guide
You will need:
•
•
A Windows–based PC or a Macintosh computer with Ethernet connectivity for configuring the Netopia 4-port
ADSL Router. This may be built-in Ethernet or an add-on card, with TCP/IP installed and configured. See
“Sharing the Connection” on page 4-1.
A DSL wall outlet wired for a connection to a telephone carrier who supports Asymmetric Digital Subscriber
Line (ADSL) connections.
Important Safety Instructions
POWER SUPPLY INSTALLATION
Connect the power supply cord to the power jack on the Netopia Router. Plug the power supply into an
appropriate electrical outlet.
CAUTION: Depending on the power supply provided with the product, either the direct plug-in power supply
blades, power supply cord plug or the appliance coupler serves as the main power disconnect. It is
important that the direct plug-in power supply, socket-outlet or appliance coupler be located so it is readily
accessible.
CAUTION (North America Only): For use only with a CSA Certified or UL Listed Limited Power Source or
Class 2 power supply, rated 12Vdc, .5A.
CAUTION (Europe Only): For use only with a GS approved Limited Power Source, rated 12Vdc, .5A.
(Sweden) Apparaten skall anslutas till jordat uttag när den ansluts till ett nätverk
(Norway) Apparatet må kun tilkoples jordet stikkontakt.
TELECOMMUNICATION INSTALLATION CAUTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce the
risk of fire, electric shock and injury to persons, including the following:
1. Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink or laundry
tub, in a wet basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote
risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
SAVE THESE INSTRUCTIONS
Making the Physical Connections 2-3
Identify the Connectors and Attach the Cables
Identify the connectors and switches on the back panel and attach the necessary Netopia Router cables.
Connect your computer, DSL line, and power source as shown.
10/100BT LAN
DSL
DC Power
4
3
LAN
2
1
Power
Off / On
Power Switch
DSL
2
1
3
1. For a direct computer to router Ethernet connection, use the standard Ethernet cable included with your
router.
2. Use the supplied DSL line cable to connect the router to your DSL wall outlet.
3. Connect the supplied power brick to a power outlet and the connector end to the router.
You should now have: the power adapter plugged in; the Ethernet cable connected between the router and your
computer; and the DSL cable connected between the router and the DSL wall outlet.
2-4 Getting Started Guide
Netopia 4-port back panel
4
3
LAN
2
1
Power
Off / On
DSL
DSL port
Power switch
Power port
Ethernet
ports
.
Port
DSL port
Description
An RJ-48 jack labeled DSL for your ADSL connection.
Ethernet ports
Four RJ-45 10/100Base-T Ethernet jacks. You can use one of these to configure the
Netopia 4-port. You can either connect your computer directly to an Ethernet port using
the supplied Category 5 Ethernet cable, or connect both your computer and the Netopia
4-port to an existing LAN environment. The Ethernet ports are auto-sensing, eliminating
the need for a crossover cable.
Power port
A DC power adapter cable connection.
An On/Off rocker switch for power.
Power switch
Making the Physical Connections 2-5
Netopia 4-port ADSL Router Status Lights
The figure below represents the Netopia 4-port ADSL Router status light (LED) panel.
Netopia 4-port ADSL Router status indicator lights
LAN 1, 2, 3, 4:
Power:
Solid green when the power is on
Solid green when Ethernet link is established
Blinks green when traffic is sent or received
over the Ethernet
DSL Sync:
Blinks green with no line attached or training,
Solid green when trained with the DSL line
2-6 Getting Started Guide
Connecting to Your Local Area Network 3-1
Chapter 3
This chapter describes how to physically connect the Netopia 4-port ADSL Router to your local area network
customize the router’s configuration for your particular LAN requirements using console-based management
(see “Telnet-Based Management” on page 5-1).
This section covers the following topics:
•
•
“Readying Computers on Your Local Network” on page 3-1
“Connecting to an Ethernet Network” on page 3-2
Readying Computers onYour Local Network
PC and Macintosh computers must have certain components installed before they can communicate through
the Netopia 4-port ADSL Router. The following illustration shows the minimal requirements for a typical PC or
Macintosh computer.
Application software
TCP/IP stack
Ethernet Driver
Your PC
or Macintosh
computer
To the Netopia 4-port ADSL Router
Application software: This is the software you use to send e-mail, browse the World Wide Web, read
TCP/IP stack: This is the software that lets your PC or Macintosh computer communicate using Internet
protocols. TCP/IP stacks must be configured with some of the same information you used to configure the
Netopia 4-port ADSL Router. There are a number of TCP/IP stacks available for PC computers. Windows 95
includes a built-in TCP/IP stack. Macintosh computers use either MacTCP or Open Transport. See “Configuring
TCP/IP on Windows-based Computers” on page 4-1. Macintosh computers use either MacTCP or Open
Transport. See “Configuring TCP/IP on Macintosh Computers” on page 4-2.
3-2 Getting Started Guide
Ethernet: Ethernet hardware and software drivers enable your PC or Macintosh computer to communicate on
the LAN.
Once the Netopia 4-port ADSL Router is properly configured and connected to your LAN, PC and Macintosh
computers that have their required components in place will be able to connect to the Internet or other remote
IP networks.
Connecting to an Ethernet Network
You can connect a standard 10/100Base-T Ethernet network to the Netopia 4-port ADSL Router using any of its
Ethernet ports.
Netopia 4-port ADSL Router back panel
4
3
LAN
2
1
Power
Off / On
DSL
If you add devices connected through a hub or switch, connect the hub or switch to an Ethernet port on the
Netopia 4-port ADSL Router.
The Netopia 4-port ADSL Router in a 10/100Base-T network
4
3
LAN
2
1
Power
Off / On
To connect your 10/100Base-T
network to the Netopia 4-port
ADSL Router through the Ethernet
port, use standard Category 5
Ethernet cables with RJ-45
connectors.
DSL
PC
PC
Macintosh
PC
Macintosh
You can attach additional devices
using standard Category 5
PC
Ethernet cables (not provided)
connected to a 10- or 100Base-T
Ethernet hub or switch. The ports
on the router will auto detect 10-
or 100Base-T. Crossover cables
are not required.
PC
Ethernet
Switch
Sharing the Connection 4-1
Chapter 4
Sharing the Connection
Once you have set up your physical local area network, you will need to configure the TCP/IP stack on each
client workstation connected to your Netopia 4-port ADSL Router. This chapter describes how to configure
TCP/IP for both Windows-based and Macintosh computers.
This chapter explains the following topics:
•
•
“Configuring TCP/IP on Windows-based Computers” on page 4-1
“Configuring TCP/IP on Macintosh Computers” on page 4-2
Configuring TCP/IP on Windows-based Computers
Configuring TCP/IP on a Windows computer requires the following:
•
•
An Ethernet card (also known as a network adapter)
The TCP/IP protocol must be “bound” to the adapter or card
Microsoft Windows
Step 1. Navigate to the TCP/IP Properties Control Panel.
a. Some Windows
Start menu -> Settings -> Control Panel ->
versions follow a path Network (or Network and Dial-up Connections
like this:
-> Local Area Connection -> Properties) ->
TCP/IP [your_network_card] or Internet
Protocol [TCP/IP] -> Properties
4-2 Getting Started Guide
b. Some Windows
Start menu -> Control Panel -> Network
versions follow a path and Internet Connections -> Network
like this:
Connections -> Local Area Connection ->
Properties -> Internet Protocol [TCP/IP]
-> Properties
Then go to Step 2.
Step 2. Select Obtain an IP address automatically.
Step 3. Select Obtain DNS server address automatically, if available.
Step 4. Remove any previously configured Gateways, if available.
Step 5. OK the settings. Restart if prompted.
NOTE: You can also use these instructions to configure other computers on your network to accept IP
addresses served by the Netopia 4-port ADSL Router.
Configuring TCP/IP on Macintosh Computers
The following is a quick guide to configuring TCP/IP for MacOS computers. Configuring TCP/IP in a Macintosh
computer requires the following:
•
You must have Open Transport installed, standard in MacOS 8 and higher and optional in earlier system
versions.
•
You must have built-in Ethernet or a third-party Ethernet card and its associated drivers installed in your
Macintosh.
Sharing the Connection 4-3
Macintosh MacOS 8 or higher or Mac OS X
Step 1. Access the TCP/IP Control Panel or Network Preference Pane.
a. MacOS follows a
path like this:
Apple Menu -> Control Panels ->
TCP/IP Control Panel
b. Mac OS X follows a Apple Menu -> System
path like this:
Preferences -> Network
Then go to Step 2.
Step 2. Select Built-in Ethernet
Step 3. Select Configure Using DHCP
Step 4. Close and Save, if prompted.
NOTE: You can use these instructions to configure other computers on your network to accept IP addresses
served by the Netopia 4-port ADSL Router.
4-4 Getting Started Guide
Telnet-Based Management 5-1
Chapter 5
Telnet-Based Management
Telnet-based management is a menu-driven interface for the capabilities built into the Netopia 4-port ADSL
Router. Telnet-based management provides access to a wide variety of features that the router supports. You
can customize these features for your individual setup. This chapter describes how to access the Telnet-based
management screens.
This section covers the following topics:
•
•
“Connecting through a Telnet Session” on page 5-2
“Navigating through the Telnet Screens” on page 5-3
Telnet-based management screens contain seven entry points to the Netopia 4-port ADSL Router configuration
and monitoring features. The entry points are displayed in the Main Menu shown below:
Netopia 4-port
Easy Setup...
WAN Configuration...
System Configuration...
Utilities & Diagnostics...
Statistics & Logs...
Quick Menus...
Quick View...
Return/Enter goes to Easy Setup -- minimal configuration.
You always start from this main screen.
•
•
The Easy Setup menus display and permit changing the values contained in the default connection profile.
You can use Easy Setup to initially configure the router directly through a Telnet session.
Easy Setup menus contain up to five descendant screens for viewing or altering these values. The number
of screens depends on whether you have optional features installed.
This manual describes the Easy Setup menus to get you up and running quickly. For more advanced
features offered in the menus listed below, see the Firmware User’s Guide.
The WAN Configuration menu displays and permits changing your connection profile(s) and default profile,
creating or deleting additional connection profiles, and configuring or reconfiguring the manner in which you
may be using the router to connect to more than one service provider or remote site.
5-2 Getting Started Guide
•
The System Configuration menus display and permit changing:
•
•
•
•
•
•
•
•
•
•
IP Setup
Filter Sets
IP Address Serving
Network Address Translation (NAT)
Date and Time
SNMP (Simple Network Management Protocol)
Security
Upgrade Feature Set
Change Device to a Bridge
Logging
•
•
•
•
The Utilities & Diagnostics menus provide a selection of seven tools for monitoring and diagnosing the
router's behavior, as well as for updating the firmware and rebooting the system.
The Statistics & Logs menus display nine sets of tables and device logs that show information about your
router, your network, and their history.
The Quick Menus screen is a shortcut entry point to 22 of the most commonly used configuration menus
that are accessed through the other menu entry points.
The Quick View menu displays at a glance current real-time operating information about your router.
Connecting through a Telnet Session
Features of the Netopia 4-port ADSL Router can be configured through the Telnet screens.
Before you can access the Telnet screens, you must have:
•
•
A network connection locally to the router or IP access to the router.
Telnet software installed on the computer you will use to configure the router
Configuring Telnet software
If you are configuring your router using a Telnet session, your computer must be running a Telnet software
program.
Telnet-Based Management 5-3
•
If you connect a PC with Microsoft Windows, you can use a Windows Telnet application or simply run Telnet
from the Start menu.
•
If you connect a Macintosh computer running Classic Mac OS, you can use the NCSA Telnet program
supplied on the Netopia CD. You install NCSA Telnet by dragging the application from the CD to your hard
disk. Mac OS X users can use the Terminal application that comes with Mac OS X in the Utilities folder.
Navigating through the Telnet Screens
Use your keyboard to navigate the Netopia 4-port ADSL Router’s configuration screens, enter and edit
information, and make choices. The following table lists the keys to use to navigate through the Telnet screens.
To...
Use These Keys...
Move through selectable items in a screen or pop-up menu
Up, Down, Left, and Right Arrow
Return or Enter
Set a change to a selected item or open a pop-up menu of
options for a selected item like entering an upgrade key
Change a toggle value (Yes/No, On/Off)
Restore an entry or toggle value to its previous value
Move one item up
Tab
Esc
Up arrow or Control + K
Down arrow or Control + O
Control + E
Move one item down
Display a dump of the device event log
Display a dump of the WAN event log
Refresh the screen
Control + F
Control + L
5-4 Getting Started Guide
Easy Setup 6-1
Chapter 6
Easy Setup
This chapter describes how to use the Easy Setup Telnet screens on your Netopia 4-port ADSL Router. After
completing the Easy Setup Telnet screens, your router will be ready to connect to the Internet or another remote
site.
Easy Setup Telnet Screens
Using four Easy Setup Telnet screens, you can:
•
•
•
Modify a connection profile for your router for the connection to your ISP or remote location
Password–protect configuration access to your Netopia 4-port ADSL Router
Accessing the Easy Setup Telnet screens
To access the Telnet screens, Telnet to the Netopia Router over your Ethernet network. See “Connecting
through a Telnet Session” on page 5-2.
Note: Before continuing, make sure you have the information that your ISP or network administrator has given
you for configuring the Netopia Router.
The Netopia Router’s first Telnet screen, Main Menu, appears in the terminal window of the attached PC or
Macintosh computer when:
•
•
•
The Netopia Router is turned on
The computer is connected to the Netopia Router
Telnet software is running and configured correctly
6-2 Getting Started Guide
Quick Easy Setup Connection Path
This section may be all you need to do to configure your Netopia 4-port ADSL Router. Your service provider will
supply you with several parameter values. Below is a handy checklist:
ADSL Line Configuration Screen
Trellis Coding Enabled
Fast Retrain Enabled
Data Link Encapsulation
❑
❑
❑
❑
❑
❑
On (default) or
Off
On (default) or
Off
RFC1483 (default) or
PPP
Data Circuit VPI
Data Circuit VPI
0-255 (8 is default)
0-65535 (35 is default)
_______________________
_______________________
Easy Setup Profile Screen
RFC1483 Mode:
Underlying Encapsulation
❑
❑
None (default) or
PPPoE
PPP Mode:
❑
Bridged 1483 (default) or
Routed 1483
❑
VC Multiplexed (default) or
LLC SNAP
❑
❑
(for PPP DLEs only)
PPP Authentication:
❑
❑
❑
None (default),
PAP or
CHAP
(for PAP or CHAP)
User Name (or Host Name):
_______________________
(for PAP or CHAP)
Password (or Secret):
_______________________
Address Translation
Enabled:
❑
❑
Yes (default) or
No
IP Addressing:
❑
❑
Numbered (default) or
Unnumbered
(for Numbered IP Addressing)
Local WAN IP Address:
_______________________
Local WAN IP Mask:
(for Unnumbered IP Addressing)
Remote IP Address:
_______________________
Remote IP Mask:
_______________________
_______________________
IP Easy Setup Screen
Ethernet IP Address:
_______________________
(192.168.1.1
255.255.255.0
are defaults)
Ethernet Subnet Mask:
Domain Name:
_______________________
_______________________
Primary Domain Name
Server:
_______________________
Secondary Domain Name
Server:
_______________________
_______________________
Default IP Gateway:
Easy Setup Security Configuration Screen
_______________________ Write Access Password:
Write Access Name:
_______________________
Easy Setup 6-3
The following steps will get you up and running quickly:
1. Open a Telnet session to 192.168.1.1 to bring up the Main Menu.
If you don't know how to do this, see “Connecting through a Telnet Session” on page 5-2.
The Main Menu appears.
Netopia 4-port
Easy Setup...
WAN Configuration...
System Configuration...
Utilities & Diagnostics...
Statistics & Logs...
Quick Menus...
Quick View...
If you do not see the Main Menu, verify that:
•
The computer used to view the Telnet screen has an Ethernet connection to the Netopia 4-port ADSL
Router’s Ethernet port. See “Connecting through a Telnet Session” on page 5-2.
•
•
Telnet is configured for the recommended values.
You have entered the correct password, if necessary. Your Netopia 4-port ADSL Router’s Telnet access may
be password protected from a previous configuration. See your system administrator to obtain the
password.
See the Firmware User’s Guide chapter on “Troubleshooting” for more suggestions.
2. Select the first item on the Main Menu list, Easy Setup. Press Return to bring up the DSL Line
Configuration menu screen.
6-4 Getting Started Guide
1. ADSL Line Configuration
ADSL Line Configuration
Trellis Coding Enabled:
Fast Retrain Enabled:
On
On
Wiring Type...
AutoSense
RFC1483
Data Link Encapsulation...
Data Circuit VPI (0-255):
8
Data Circuit VCI (32-65535):
35
PREVIOUS SCREEN
NEXT SCREEN
Return/Enter brings you to next screen.
1. Select Trellis Coding Enabled. Toggle it to On (the default) or Off. Unless otherwise specified by your
provider, you can accept this default.
2. Select Fast Retrain Enabled. Toggle it to On (the default) or Off. Unless otherwise specified by your
provider, you can accept this default.
3. Select Data Link Encapsulation and from the pop-up menu choose either RFC1483 (the default) or PPP.
4. The next two fields, Data Circuit VPI and Data Circuit VCI are editable. Enter the Virtual Path Identifier and
Virtual Channel Identifier values that your provider specifies. VPI 8/VCI 35 are the most common. Your
provider must specify these values.
5. Press the Down arrow key until you reach NEXT SCREEN. Press Return to bring up the next screen.
Easy Setup 6-5
2. Easy Setup Profile
The Easy Setup Profile screen is where you configure the parameters that control the Netopia 4-port ADSL
Router’s connection to a specific remote destination, usually your ISP or a corporate site. On a Netopia 4-port
ADSL Router you can add up to 15 more connection profiles, for a total of 16, although you can only use one at
a time, unless you are using Virtual Private Networks (VPNs).
Connection Profile 1: Easy Setup Profile
+--------------+
Connection Profile 1: Easy Setup Profile
Underlying Encapsulation...
+--------------+
| Bridged 1483 |
| Routed 1483 |
+--------------+
Underlying Encapsulation...
None
RFC1483 Mode...
PPP Mode...
VC Multiplexed
None
PPP Authentication...
Address Translation Enabled:
IP Addressing...
Yes
Address Translation Enabled:
IP Addressing...
Yes
Numbered
Numbered
Local WAN IP Address:
Local WAN IP Mask:
0.0.0.0
0.0.0.0
Local WAN IP Address:
Local WAN IP Mask:
Remote IP Address:
Remote IP Mask:
0.0.0.0
0.0.0.0
127.0.0.2
255.255.255.255
PREVIOUS SCREEN
NEXT SCREEN
PREVIOUS SCREEN
NEXT SCREEN
Enter basic information about your WAN connection with this screen.
If you selected RFC1483 in the previous screen, the
Easy Setup Profile screen allows you to choose
PPPoE or None as the Underlying Encapsulation.
If you selected PPP in the previous screen, the Easy
Setup Profile screen allows you to choose PPPoE or
None as the Underlying Encapsulation.
•
If you choose None, the RFC1483 Mode offers
the choice of Bridged 1483 or Routed 1483.
•
If you choose None, the PPP Mode offers the
choice of VC Multiplexed or LLC SNAP.
•
If you choose PPPoE, a PPP Authentication
option appears, to permit you to select PAP or
CHAP authentication (or None), and fields to
enter PAP User Name and Password, or CHAP
Host Name and Secret.
•
The PPP Authentication option permits you to
select PAP or CHAP authentication (or None),
and fields to enter PAP User Name and
Password, or CHAP Host Name and Secret.
1. To enable address translation, toggle Address Translation Enabled to Yes (the default). You need not
change this unless you have a specific reason. For more information on Network Address Translation, see
the Firmware User’s Guide chapter on “Multiple Network Address Translation (MultiNAT)“.
2. Depending on your Data Link Encapsulation selections, either Numbered or Unnumbered IP Addressing
may be enabled by default. (You may choose either from the pop-up menu, if specifically instructed to do
so.) Unless otherwise specified by your service provider, accept the defaults, and do not change the next
two values. They will be supplied by your ISP.
3. Press the Down arrow key until you reach NEXT SCREEN. Press Return to bring up the next screen.
6-6 Getting Started Guide
3. IP Easy Setup
The IP Easy Setup screen is where you enter information about your Netopia Router’s:
•
•
•
•
•
Ethernet IP address
Ethernet Subnet mask
Domain Name
Domain Name Server IP address
Default gateway IP address
Consult with your network administrator to obtain the information you will need. For more information about
setting up IP, see the Firmware User’s Guide chapter on “IP Setup”.
IP Easy Setup
Ethernet IP Address:
Ethernet Subnet Mask:
192.168.1.1
255.255.255.0
Domain Name:
Primary Domain Name Server:
Secondary Domain Name Server:
209.3.224.21
209.3.224.20
Default IP Gateway:
IP Address Serving:
127.0.0.2
On
Number of Client IP Addresses:
1st Client Address:
100
192.168.1.100
PREVIOUS SCREEN
NEXT SCREEN
Enter an IP address in decimal and dot form (xxx.xxx.xxx.xxx).
Set up the basic IP & IPX attributes of your Netopia in this screen.
1. Select Ethernet IP Address and enter the first IP address from the IP address range your ISP has given you
only if you are not using Network Address Translation (NAT). This will be the Netopia Router’s IP address.
The Ethernet IP Address defaults to an address (192.168.1.1) within a range reserved by the Internet
address administration authority for use within private networks.
Because this is a private network address, it should never be directly connected to the Internet. Using NAT
for all your connection profiles will ensure this restriction. See the Firmware User’s Guide chapter on
“Multiple Network Address Translation (MultiNAT)” for more information.
2. Select Ethernet Subnet Mask and enter the subnet mask your ISP has given you only if you are not using
NAT. The Ethernet Subnet Mask defaults to a standard class mask derived from the class of the Ethernet IP
address you entered in the previous step.
3. Press the Down arrow key until the editable field labeled Domain Name is highlighted.
If you have a static IP Address, that is, one that is permanently assigned by your ISP and never changes,
type the Domain Name your ISP gave you. Press Return. The next field Primary Domain Name Server will
be highlighted. If you are using DHCP or PPPoE, leave this field blank and skip Step 4.
Easy Setup 6-7
4. Type the Primary Domain Name Server address your ISP gave you. Press Return. A new field Secondary
Domain Name Server will appear. If your ISP gave you a secondary domain name server address, enter it
here. Press Return until the next field Default IP Gateway is highlighted.
5. If you do not enter a Default IP Gateway value, the router defaults to the remote IP address you entered in
the Easy Setup connection profile. If the Netopia Router does not recognize the destination of any IP traffic,
it forwards that traffic to this gateway.
Do not confuse the remote IP address and the Default IP Gateway’s address with the block of local IP
addresses you may receive from your ISP. You use the local IP addresses for the Netopia 4-port ADSL
Router’s Ethernet port and for IP clients on your local network. The remote IP address and the default
gateway’s IP address should point to your ISP’s router.
6. Toggle IP Address Serving to On or Off, depending on whether you want the device’s IP address server to
supply dynamic IP addresses to your client workstations. Normally, you would accept the default On so that
workstations on your LAN can have IP addresses assigned dynamically from the router.
7. The Netopia Router’s built-in IP address server will provide 100 IP addresses automatically to workstations
on your LAN. You only need to change the Number of Client IP Addresses if you have some other IP
addressing scheme.
8. By default, the 1st Client Address is 192.168.1.100, based on the device’s default IP address of
192.168.1.1. You only need to change this if you have some other IP addressing scheme.
9. Press the Down arrow key until you reach NEXT SCREEN. Press Return.
6-8 Getting Started Guide
4. Easy Setup Security Configuration
The Easy Setup Security Configuration screen lets you password-protect your Netopia 4-port ADSL Router. Input
your Write Access Name and Write Access Password with names or numbers totaling up to eleven digits.
If you password protect the Telnet screens, you will be prompted to enter the name and password you have
specified every time you log in to the Telnet screens. Do not forget your name and password. If you do, you will
be unable to access any of the configuration screens.
Additional security features are available. See the Firmware User’s Guide chapter on “Security”.
Easy Setup Security Configuration
It is strongly suggested that you password-protect configuration access to your
Netopia. By entering a Name and Password pair here, access via serial,
Telnet, and Web Server will be password-protected.
Be sure to remember what you have typed here, because you will be prompted for
it each time you configure this Netopia.
Write Access Name:
Write Access Password:
PREVIOUS SCREEN
TO MAIN MENU
RESTART DEVICE
Configure a Configuration Access Name and Password here.
The final step in configuring the Easy Setup Telnet screens is to restart the Netopia 4-port ADSL Router, so that
the configuration settings take effect.
1. Select RESTART DEVICE. A prompt asks you to confirm your choice.
2. Select CONTINUE to restart the Netopia Router and have your selections take effect.
Note: You can also restart the system at any time by using the Restart System utility in the Utilities and
Diagnostics menu, or by turning the Netopia Router off and on with the power switch.
The Router will restart and your configuration settings will be activated. You can then Exit or Quit your Telnet
application.
Easy Setup is now complete.
Technical Specifications and Safety Information A-1
Appendix A
Technical Specifications and Safety
Information
Description
Dimensions: 13.5 cm (w) x 13.5 cm (d) x 3.5 cm (h) 5.25” (w) x 5.25” (d) x 1.5” (h)
Communications interfaces: The Netopia 4-port Router has an RJ-45 jack for WAN line connections and a
4–port 10/100Base-T Ethernet switch for your LAN connections.
Power requirements
•
•
12 VDC input
.5 amps
Environment
Operating temperature: 0° to +40° C
Storage temperature: 0° to +70° C
Relative storage humidity: 20 to 80% noncondensing
Software and protocols
Software media: Software preloaded on internal flash memory; field upgrades done via download to internal
flash memory via TFTP or web upload.
Routing: TCP/IP Internet Protocol Suite, RIP
WAN support: PPPoE, DHCP, static IP address
Security: PAP, UI password security
Management/configuration methods: HTTP (Web server), Telnet
Diagnostics: Ping, event logging, routing table displays, statistics counters, web-based management
Agency approvals
North America
Safety Approvals:
A-2 Getting Started Guide
•
•
United States – UL: 1950 Third Edition
Canada – CSA: CAN/CSA-C22.2 No. 950-95
EMC:
•
•
United States – FCC Part 15 Class B
Canada – ICES-003
Telecom:
•
•
United States – FCC Part 68
Canada – CS-03
International
Safety Approvals:
•
•
Low Voltage (European directive) 73/23
EN60950 (Europe)
EMI Compatibility:
•
•
•
89/336/EEC (European directive)
EN55022:1994 CISPR22 Class B
EN300 386 V1.2.1
Regulatory notices
European Community. This Netopia product conforms to the European Community CE Mark standard for the
design and manufacturing of information technology equipment. This standard covers a broad area of product
design, including RF emissions and immunity from electrical disturbances.
The Netopia 4-port ADSL Router complies with the following EU directives:
•
•
Low Voltage, 73/23/EEC
EMC Compatibility, 89/336/EEC, conforming to EN 55 022
Manufacturer’s Declaration of Conformance
Note: Warnings:
This is a Class B product. In a domestic environment this product may cause radio interference, in which case
the user may be required to take adequate measures. Adequate measures include increasing the physical
distance between this product and other electrical devices.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
Technical Specifications and Safety Information A-3
United States. This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio TV technician for help.
Service requirements. In the event of equipment malfunction, all repairs should be performed by our Company
or an authorized agent. Under FCC rules, no customer is authorized to repair this equipment. This restriction
applies regardless of whether the equipment is in or our of warranty. It is the responsibility of users requiring
service to report the need for service to our Company or to one of our authorized agents. Service can be
obtained at Netopia, Inc., 6001 Shellmound Street, Emeryville, California, 94608.
Note: Important
This product was tested for FCC compliance under conditions that included the use of shielded cables and
connectors between system components. Changes or modifications to this product not authorized by the
manufacturer could void your authority to operate the equipment.
Canada. This Class B digital apparatus meets all requirements of the Canadian Interference -Causing
Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilleur du
Canada.
Declaration for Canadian users
The Canadian Industry Canada label identifies certified equipment. This certification means that the equipment
meets certain telecommunications network protective, operation, and safety requirements. The Department
does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of
the local telecommunications company. The equipment must also be installed using an acceptable method of
connection. In some cases, the company’s inside wiring associated with a single line individual service may be
extended by means of a certified connector assembly (telephone extension cord). The customer should be
aware that compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to the certified equipment should be made by an authorized Canadian maintenance facility designated
by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may
give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility,
telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution
may be particularly important in rural areas.
A-4 Getting Started Guide
Caution
Users should not attempt to make such connections themselves, but should contact the appropriate electric
inspection authority, or electrician, as appropriate.
The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum
number of terminals allowed to be connected to a telephone interface. The termination on an interface may
consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence
Numbers of all the devices does not exceed 5.
Important Safety Instructions
Australian Safety Information
The following safety information is provided in conformance with Australian safety requirements:
Caution
DO NOT USE BEFORE READING THE INSTRUCTIONS: Do not connect the Ethernet ports to a carrier or carriage
service provider’s telecommunications network or facility unless: a) you have the written consent of the network
or facility manager, or b) the connection is in accordance with a connection permit or connection rules.
Connection of the Ethernet ports may cause a hazard or damage to the telecommunication network or facility,
or persons, with consequential liability for substantial compensation.
Caution
•
The direct plug-in power supply serves as the main power disconnect; locate the direct plug-in power supply
near the product for easy access.
•
For use only with CSA Certified Class 2 power supply, rated 12VDC, 1.0A.
Telecommunication installation cautions
•
•
•
Never install telephone wiring during a lightning storm.
Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at
the network interface.
•
•
Use caution when installing or modifying telephone lines.
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk
of electric shock from lightning.
•
Do not use the telephone to report a gas leak in the vicinity of the leak.
Technical Specifications and Safety Information A-5
47CFR Part 68 Information
FCC Requirements
1. The Federal Communications Commission (FCC) has established Rules which permit this device to be
directly connected to the telephone network. Standardized jacks are used for these connections. This
equipment should not be used on party lines or coin phones.
2. If this device is malfunctioning, it may also be causing harm to the telephone network; this device should
be disconnected until the source of the problem can be determined and until repair has been made. If this
is not done, the telephone company may temporarily disconnect service.
3. The telephone company may make changes in its technical operations and procedures; if such changes
affect the compatibility or use of this device, the telephone company is required to give adequate notice of
the changes. You will be advised of your right to file a complaint with the FCC.
4. If the telephone company requests information on what equipment is connected to their lines, inform them
of:
a. The telephone number to which this unit is connected.
b. The ringer equivalence number. [0.XB]
c. The USOC jack required. [RJ11C]
d. The FCC Registration Number. [XXXUSA-XXXXX-XX-E]
Items (b) and (d) are indicated on the label. The Ringer Equivalence Number (REN) is used to determine
how many devices can be connected to your telephone line. In most areas, the sum of the REN's of all
devices on any one line should not exceed five (5.0). If too many devices are attached, they may not ring
properly.
FCC Statements
a) This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the
bottom of this equipment is a label that contains, among other information, a product identifier in the format
US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
b) List all applicable certification jack Universal Service Order Codes (“USOC”) for the equipment: RJ11.
c) A plug and jack used to connect this equipment to the premises wiring and telephone network must comply
with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and
modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is
also compliant. See installation instructions for details.
d) The REN is used to determine the number of devices that may be connected to a telephone line. Excessive
RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not
all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be
connected to a line, as determined by the total RENs, contact the local telephone company. For products
approved after July 23, 2002, the REN for this product is part of the product identifier that has the format
US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3).
For earlier products, the REN is separately shown on the label.
A-6 Getting Started Guide
e) If this equipment, the Netopia ENT Enterprise Series router, causes harm to the telephone network, the
telephone company will notify you in advance that temporary discontinuance of service may be required. But if
advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you
will be advised of your right to file a complaint with the FCC if you believe it is necessary.
f) The telephone company may make changes in its facilities, equipment, operations or procedures that could
affect the operation of the equipment. If this happens the telephone company will provide advance notice in
order for you to make necessary modifications to maintain uninterrupted service.
g) If trouble is experienced with this equipment, the Netopia ENT Enterprise Series router, for repair or warranty
information, please contact:
Netopia Technical Support
510-597-5400
If the equipment is causing harm to the telephone network, the telephone company may request that you
disconnect the equipment until the problem is resolved.
h) This equipment not intended to be repaired by the end user. In case of any problems, please refer to the trou-
bleshooting section of the Product User Manual before calling Netopia Technical Support.
i) Connection to party line service is subject to state tariffs. Contact the state public utility commission, public
service commission or corporation commission for information.
j) If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of
this Netopia ENT Enterprise Series router does not disable your alarm equipment. If you have questions about
what will disable alarm equipment, consult your telephone company or qualified installer.
Electrical Safety Advisory
Telephone companies report that electrical surges, typically lightning transients, are very destructive to
customer terminal equipment connected to AC power sources. This has been identified as a major nationwide
problem. Therefore it is advised that this equipment be connected to AC power through the use of a surge
arrestor or similar protection device.
|