Attachment
Model CH7241U
Instruction manual
(with warranty card)
Safety precautions
WARNING
Denotes risk of personal injury, loss of life or damage to the tool
In case of nonobservance of the instructions in this manual.
Before use, be sure to carefully read the instructions. Read the related screwdriver instruction manual,
too.
Be sure to wear protective goggles during work.
Be sure to wear a dust-proof mask during work.
Depending on the work environment, wear ear protectors, hardhat, working shoes, and other safety gear.
Be sure to use the specified Adaptor Kit that is dedicated to your screwdriver model.
Be sure to use the specified "VISROPE STRIPS" connecting screws.
Ensure solid footing and hold yourself in a safety-first position.
Wear clothes proper for work.
Keep the workplace in order and well lit.
When working in an elevated place, make sure there is nobody beneath. Be very careful not to let this
unit and screws fall.
Never direct this unit toward anybody.
Never keep your hands, feet and head close to the tip (screw outlet) of the unit during work.
Keep the unit away from open fire and flame.
Do not use the unit near volatile, flammable substances such as gasoline, thinner, gas, paint, and
adhesive. The unit may catch fire or explode.
Do not use the unit in rain, or water-splashed, wet or humid area. Do not leave the unit in rain, either.
Keep the unit, accessories and consumable parts without reach of children.
For after-use handling, refer to "Maintenance and inspection".
Handle the unit with enough care. Dropping or hitting may result in malfunction.
Keep these instructions in the safe place.
Specifications
MODEL: CH7241U
Length (without accessories)
Weight (without accessories)
Approx. 216 mm
Approx. 350 g
Depth adjustment
(countersunk and flat-head screws)
Applicable screw Countersunk and flat-head
-6 mm (shallow)
+7 mm (deep)
25 to 41 mm
lengths
screws
Pan-head drilled screws
19 mm
Adjusting the screw-driving depth
Turn the screw depth adjusting dial upward to achieve
more depth.
Turn the screw depth adjusting dial downward to
achieve less depth.
Four clicks make an increment of 1 mm.
Approximate standard depths (0 mm deep)
Countersunk and
flat-head screws
Pan-head screws
Attaching and detaching the specific connecting screws
Attaching
Place the VISROPE
STRIPS in the direction
shown in the figure.
Detaching
Hold
down
the
connecting screw take-out
button.
Draw out the VISROPE
STRIPS.
Tightening the screws
Set the screwdriver's trigger
switch to the ON position.
Press the lock button for
continuous screw tightening.
Apply and push the tool
perpendicular onto the work. The
CH7241 stops at the end of a
stroke. The screwdriver's clutch is
then activated to completely tighten
up the screw.
Troubleshooting
Two screws fed at once, or screw jammed and stuck.
Hold down the connecting screw
take-out button.
Lower the feed lever.
Make sure the screws go
smoothly, and draw out the
VISROPE STRIPS.
Maintenance and inspection
1.After each use, be sure to clean up the unit. Powder plaster, dust and dirt stuck on the unit may get it in
trouble.
2.To wipe the unit clean, use dry cloth or neutral detergent-soaked cloth. Do not use gasoline, thinner or the
like, which would damage the unit. Never wash the unit in water, which would get it rusty or malfunctioning.
3.The bit of the specific adaptor kit is consumable. If its both heads have worn out, immediately replace it
with new one. Worn-out bit may cause poor tightening or damage the screw head.
4.Store the unit in a dry, cool place. Keep it without reach of children. Avoid any unstable spot to store the
unit on.
5.Do not disassemble and repair the unit yourself. For repairs, contact your dealer.
VISLIDER Auto Feed Screwdriving Attachment
CH7000 Attachment Warranty Card
6 month after date of purchase
CH7241U
Model
Date of purchase
Names
Warranty period
Address
Phone
Address
Name
Phone
Make sure that the above form is filled out. This warranty shall be invalid if the *-marked information is missing.
1.If within the warranty period the unit fails due to defect in material or workmanship, the manufacturer will
repair the unit free of charge.
2.To ask for free repair within the warranty period, please take the unit and this warranty card with you to
your dealer.
3.Even within the warranty period, the following cases are not covered by this warranty.
a) Troubles or damages due to wrong handling and use or through tampering with the unit.
b) Troubles or damages due to dropping or rough handling during moving or transport.
c) Troubles or damages due to fire, earthquake, flood, lightning, and other natural disasters and pollution.
d) Troubles or damages due to poor storage and negligence in maintenance.
e) Loss or missing of this warranty card.
f) No date of purchase, customer's names and address, or dealer's name and address entered in this
warranty card. Or forged document.
4.If you want an engineer sent to you for repairing this product, you will be charged for his or her travel
expenses and labor.
5.This warranty card will never be reissued. Keep it in a safe place.
This warranty covers free repairs within the written warranty period and under the condition of proper use.
This card is not intended to restrict the user's legal rights. For repairs after the warranty period, contact your
dealer or the Customers' Services of MURO NORTH AMERICA INC. or MURO CORPORATION.
1-4-10 Kaminoge, Setagaya-ku, Tokyo, JAPAN 158-0093
TEL: +81-03-3703-4122 FAX: +81-03-3704-2348
7 Tilbury Crt, Brampton, Ontario, CANADA L6T 3T4
TEL: (905) 451-7667 FAX: (905) 451-7936
7241M02U –
2000.1.21
Printed in Japan
|